Beautify landscaping can take many different forms in order to take a rather plain looking yard and turn it into something spectacular. A popular way is to install some sort of water display. With a pondless waterfall kit, you can do just that. Built correctly, you end up with a natural looking fall and stream that recycles the water for continuous pleasure.
Start the project by deciding where you want it. With this design, you want to include the entire flow so you can plan correctly and have a gravity fed stream. After having the utility company mark any lines, you should use bright spray paint to mark the bottom, where the pump will sit. Also, mark or get an idea of where the top of the fall will be and mark it as well.
When you dig, there are several things that need to be done just right. First, the reservoir needs to sit below the stream path. You will want to dig 18 to 24 inches deep and in a large square or circle. Then you will need to dig a deeper hole to place the pump vault. This needs to be the lowest point of the reservoir in order for all the water to be recirculated. Save the dirt to use for fill and covering the pipe and lining.
Using rubber liner, you will protect the ground where the water will flow. You want to cover the entire reservoir and where the stream will be. Once this is covered, place the vault in the hole. Using more than one layer of the liner will be helpful in protecting it from getting poked by the rocks and keeping the water from draining out into the yard.
Run the flexible tubing to the top of the fall. You may want to dig a trench, but you can easily use the leftover dirt to cover it with several inches without digging a trench. Keep it uncovered until the last step. It will be attached to the spillway at the top to create a circulating water system.
Use bigger gravel in the bottom and begin filling in the reservoir. Dirt and sand can wash away and become saturated. The rocks will hold everything in place. As you build it up, begin adding larger rocks, even boulder size, for decoration. You will begin placing them along the path of the stream up to the spillway.
The larger boulders can be used in various points to create additional spillways and paths. When these are in place, begin filling in areas with different types of rocks and gravel for decorative purposes and to create a natural stream. Before you're done, run water through the system to see where the water path will go and adjust the rocks and liner as needed.
Once things are set, finish filling in the stream and cover the flexible tubing. Using the leftover dirt, you can cover the tubing and any liner that is exposed outside of the water flow. Dirt will wash away, so anyplace the water flows should be covered with rocks and decorative gravel. After this is done, you can begin putting in plants, flowers, leaves, or other decorative natural items to help complete the scene.
Start the project by deciding where you want it. With this design, you want to include the entire flow so you can plan correctly and have a gravity fed stream. After having the utility company mark any lines, you should use bright spray paint to mark the bottom, where the pump will sit. Also, mark or get an idea of where the top of the fall will be and mark it as well.
When you dig, there are several things that need to be done just right. First, the reservoir needs to sit below the stream path. You will want to dig 18 to 24 inches deep and in a large square or circle. Then you will need to dig a deeper hole to place the pump vault. This needs to be the lowest point of the reservoir in order for all the water to be recirculated. Save the dirt to use for fill and covering the pipe and lining.
Using rubber liner, you will protect the ground where the water will flow. You want to cover the entire reservoir and where the stream will be. Once this is covered, place the vault in the hole. Using more than one layer of the liner will be helpful in protecting it from getting poked by the rocks and keeping the water from draining out into the yard.
Run the flexible tubing to the top of the fall. You may want to dig a trench, but you can easily use the leftover dirt to cover it with several inches without digging a trench. Keep it uncovered until the last step. It will be attached to the spillway at the top to create a circulating water system.
Use bigger gravel in the bottom and begin filling in the reservoir. Dirt and sand can wash away and become saturated. The rocks will hold everything in place. As you build it up, begin adding larger rocks, even boulder size, for decoration. You will begin placing them along the path of the stream up to the spillway.
The larger boulders can be used in various points to create additional spillways and paths. When these are in place, begin filling in areas with different types of rocks and gravel for decorative purposes and to create a natural stream. Before you're done, run water through the system to see where the water path will go and adjust the rocks and liner as needed.
Once things are set, finish filling in the stream and cover the flexible tubing. Using the leftover dirt, you can cover the tubing and any liner that is exposed outside of the water flow. Dirt will wash away, so anyplace the water flows should be covered with rocks and decorative gravel. After this is done, you can begin putting in plants, flowers, leaves, or other decorative natural items to help complete the scene.
About the Author:
Get a summary of the factors to consider when choosing a pondless waterfall kit supplier and more information about a reputable supplier at http://www.boulderfountain.com/pondless-waterfall.html now.
No comments:
Post a Comment